Adtran 2x64 Setup Notes

For use on dual 64k data channels with a combination of two DCB muxes or routers

We recommend dialing remotes from the host.

• Press ENTER
• Press 3 (Config)
• Press ENTER
• Press 1 (Netw. options)
• Press ENTER
• Press 1 (Dial Line)
• Press ENTER
• Press 1 (Switch Protocl)
• Press ENTER
• Press 3 (National ISDN1) or whatever telco says you have!
• Press ENTER
• Press 3 (Terminal ID)
• Press ENTER
• Press 1 (Set SPID)
• Press ENTER (Select SPID dte1)
• Press ENTER (Enter SPID dte1)
• Press number keys to enter full first SPID {ie, 21735971950111)
• Press ENTER (SAVING NUMBER)
• Press ^ (Select SPID dte2)
• Press ENTER (Enter SPID dte2)
• Press number keys to enter full second SPID {ie, 21735971960111)
• Press ENTER (SAVING NUMBER)
• Press CANCEL (Set SPID)
• Press 2 (Set LDN)
• Press ENTER (Select LDN dte1)
• Press ENTER (Enter LDN dte1)
• Press number keys to enter first directory number {ie, 3597195}
• Press ENTER (SAVING NUMBER)
• Press ^ (Select LDN dte2)
• Press ENTER (Enter LDN dte2)
• Press number keys to enter second directory number {ie, 3597196}
• Press ENTER (SAVING NUMBER)
• Press CANCEL (Set LDN)
• Press CANCEL (Terminal ID)
• Press CANCEL (Dial Line)
• Press CANCEL (Netw. options)
• Press 2 (DTE options)
• Press ENTER (OPTIONS dte#1)
• Press ENTER (Synchronous)
• Press ENTER (Bit Rate)
• Press 2 (Connector Type)
• Press ENTER (RS-530)
• Press 3 (RS-232)
• Press ENTER (Connector Type)
• Press 5 (CD Options)
• Press ENTER (Normal)
• Press ENTER (CD Options) At this point CS and SR LEDs should go on
• Press 6 (DTR Options)
• Press ENTER (Ignore DTR)
• Press 5 (Dial #0 if On) HOST ONLY!
• Press ENTER (DTR Options)
• Press CANCEL (Options dte#1)
• Press ^ (Options dte#2)
• Press ENTER (Synchronous)
• Press ENTER (Bit Rate)
• Press 2 (Connector Type)
• Press ENTER (RS-530)
• Press 3 (RS-232)
• Press ENTER (Connector Type)
• Press 5 (CD Options)
• Press ENTER (Normal)
• Press ENTER (CD Options) At this point CS and SR LEDs should go on
• Press 6 (DTR Options)
• Press ENTER (Ignore DTR)
• Press 5 (Dial #0 if On) HOST ONLY!
• Press ENTER (DTR Options)
• Press CANCEL (OPTIONS dte#2)
• Press CANCEL (DTE options)
• Press CANCEL (CONFIG) REMOTE UNIT CONFIG ENDS HERE - Press CANCEL again to return to main status screen.
• Press 4 (DIAL)
• Press ENTER (DIAL dte#1)
• Press ENTER (Hang up line)
• Press 6 (Store/Review #)
• Press ENTER (Select SN0)
• Press ENTER (Enter/change SN0)
• Press number keys to enter remote TA dialing number. Usually this would be the same as the seven digit directory number {ie, 3597193} of the same DTE port of the remote TA, however Centrex lines may only require 3 or 4 digits to dial to prevent access to an outside line. In this case enter only the 4 digit suffix portion of the directory number. Do not try to use only three digits as this seems to confuse most TAs.
• Press ENTER (Select SN0)
• Press CANCEL (DIAL dte#1)
• Press ^ (DIAL dte#2)
• Press ENTER (Hang up line)
• Press 6 (Store/Review #)
• Press ENTER (Select SN0)
• Press ENTER (Enter/change SN0)
• Press number keys to enter remote TA dialing number.
• Press ENTER (Select SN0)
• Press CANCEL (DIAL dte#2)
• Press CANCEL (DIAL)
• Press CANCEL {main status screen}