|
|
|
----------
Map34 V3.01 Release Notes 04/30/2024
1.0 INTRODUCTION
New major version release of Map34. Map34 development has been moved to Microsoft Visual Studio 2019 and will subsequently utilize the VS 2019 Run-Time.
This release adds the following features:
Support for performing file transfers with a third-party TFTP or SFTP server. Currently, SFTP transfers are only supported by the CCB controller.
This release corrects the following:
Map34 would report a mapping verification error when mapping the 6UDTEA card set for mode 1. The cross-connect would be created but would not be displayed by Map34.
Map34 would report an “unknown failure” error, when updating controller firmware on the CCPB-2GE and CCPB-8GE controllers. Although the firmware update would eventually succeed, Map34 was receiving a status code that it did not understand and would throw the error. The status codes were specific to PTN feature of the controllers.
Map34 could not create, nor could it read cross-connects with the single-port mini OCU/DP card.
This release adds the ability to copy a “Circuit Info” text string, from the Circuit Info View to the system clipboard. This will make the text string available for pasting.
----------
Map34 V2.14 Release Notes 8/28/2023
1.0 INTRODUCTION
This release adds the ability to copy a “Circuit Info” text string, from the Circuit Info View to the system clipboard. This will make the text string available for pasting.
----------
Map34 V2.13 Release Notes 4/04/2023
1.0 INTRODUCTION
This release corrects a compatibility issue with the AM3440 CCPB controller and the 8-EM card. When cross-connecting an 8-EM port to a Pseudo-Wire channel, Map34 would throw a mapping verification error even though the cross-connect was successful created.
----------
Map34 V2.12 Release Notes 3/14/2023
1.0 INTRODUCTION
This release corrects two compatibility issues with the AM3440-E.
Cross-connects between the pseudo-wire ports and certain tributary cards may not display correctly after restoring the system from a saved configuration file.
The port names, used in the map export file, were not consistent for pseudo-wire ports.
----------
Map34 V2.11 Release Notes 2/07/2023
1.0 INTRODUCTION
This release adds the following feature:
Added support for the AM3440 CCPB-2GE controller in a ‘C’ chassis.
This release corrects the following:
The new version of PuTTY, included in the v2.10 release, requires the Visual C++ 2019 Runtime libraries be installed on the system. While these libraries are usually already available on the system, there is no guarantee they are installed. The Map34 installer was modified to include the Visual C++ 2019 Runtime installer.
The Visual C++ 2019 Runtime libraries need only be installed once. After that, Windows system update will automatically update the libraries. A checkbox in the Map34 installer will allow the user to choose whether to Launch the Visual C++ 2019 Runtime installer. If the libraries are already installed, the installation will fail and display a message indicating a newer version of the libraries are already present on the system.
----------
Map34 V2.10 Release Notes 12/07/2022
1.0 INTRODUCTION
This release adds the following features:
Added support for the AM3440 CCPB-8GESHW.
Added support for unframed pseudo-wire cross-connects.
Redesign of Map34 firmware upgrades.
Redesign of Map34 controller and card resets following firmware upgrade.
Added support for resetting controller and cards from Map34 – Tools.
Added support for upgrading card FPGA code.
Added support for upgrading the bootloader code.
Modified Map34 for backward compatibility with old AM3440 CCA firmware, starting with v8.31.03, and cards 4T1, 8RS232-RJ, 8RS232-DB, 8EM, 8EMA, 12FXS, 12FXSA, RTA.
The Map34 package now includes two version of PuTTY, v0.77 (released in 2022) and an unlabeled version from 2014. Map34 will selectively launch PuTTY based on the AM3440 firmware version. This is to address SSL compatibility.
----------
Map34 V2.09 Release Notes 08/08/2022
1.0 INTRODUCTION
This release adds the following features:
Added support for the 8SRU card.
Added a feature to enable/disable telnet and SSH in the AM3440 via SNMP commands. A customer had accidentally disabled both telnet and ssh access to his units. This feature allowed him to remotely reenable these services. The feature is found under the “Tools” menu, “Enable Telnet/SSH”.
----------
Map34 V2.08 Release Notes 01/28/2022
1.0 INTRODUCTION
This release adds the following features:
- Support for the CCPB-DCS controller.
- Support for the CCPB-2g controller.
- Support for SNMPv3 AES Privacy.
To support AES encryption, the libeay32.dll crypto library has been added to the Map32 install package. This library may cause a false anti-virus warning.
----------
Map34 V2.07 Release Notes 9/1/2020
1.0 INTRODUCTION
Support for Support for ABRA card, mode 2 (Voice Protection).
----------
Map34 V2.06 Release Notes 3/17/2020
1.0 INTRODUCTION
This release corrects the following:
Support for the VoIP card was added.
A feature to pull FAE package was added. This appears under the "File - Transfer" menu.
This release corrects the following:
Corrected a TFTP protocol problem when sending files to the device. This only affected transfers where there was no TFTP option negotiation.
----------
Map34 V2.04 Release Notes 11/26/2019
1.0 INTRODUCTION
This release corrects the following:
A "Tools - Retrieve" operation would cause port duplication in the drop-down port list for each card.
There was a protocol bug in the TFTP server. Duplicate acknowledgments received from the client device, would cause the server to unnecessarily resend data that had already been acknowledged.
----------
Map34 V2.03 Release Notes 10/25/2019
1.0 INTRODUCTION
This release adds the following features:
Support for 5-port X.50 card.
A configuration file can be specified as a command-line argument to Map34.exe. This will be used as the default configuration file. The purpose of this is to allow users to create shortcuts that load a specific configuration file. The user must specify the full path to the configuration file. If there are any space characters in the full path name, the entire path must be enclosed in double quotes.
----------
Map34 V2.02 Release Notes 8/12/2019
1.0 INTRODUCTION
This release adds support for the AM3440E chassis.
This release corrects the following:
There was a error in the Circuit-Info navigation. Double clicking on a circuit in the Circuit-Info window should cause the Map Display to show the circuit. However, for some trib cards, the wrong port would be displayed.
----------
Map34 V2.01 Release Notes 2/12/2019
1.0 INTRODUCTION
This release add support for the following features:
Setting the XCtype, 1:1 or 1:N, at map time. This feature is available for both the CCA and CCB controllers.
Support for CCB Circuit Info feature. This includes setting the Circuit Info at map time and a new view for modifying and searching Circuit info.
Format of CSV export file modified to include the Circuit Info. This will only apply to the CCB controllers. For CCA controller, the export file will retain the original format.
----------
Map34 V1.24 Release Notes 9/19/2018
1.0 INTRODUCTION
This release adds support for the 6UDTEA card.
Loop added a new status code, 101 - "ok - need cold reset", to the file-transfer/firmware upgrade. Map34 was updated to support this new code.
Potential Issues:
There appears to be an AM3440 mapping bug when this card is configured for mode 1, "v1.110". In this mode, the card presents as having 6 Ports, each corresponding to a DS0. In both the CLI and SNMP, if you attempt to do a group map, the system will throw a "range" error. It will only allow 1 port to be mapped at a time.
----------
Map34 V1.23 Release Notes 2/1/2018
1.0 INTRODUCTION
This release is for all versions of Map34.
This release adds support for the CXR-QX3440. This release is specifically for NASA. There is no need for other customers to upgrade from v1.22.
----------
Map34 V1.22 Release Notes 12/152016
1.0 INTRODUCTION
This release is for all versions of Map34.
This release corrects the following:
When working with AM3440-B and AM3440-C chassis, if a double-slot card is installed in the chassis, it was not possible to select the card by clicking on the card's graphic on the GUI interface.
----------
Map34 V1.21 Release Notes 7/25/2016
1.0 INTRODUCTION
This release is for all versions of Map34.
Loop added two new error codes to the firmware update/copy to redundant status. Map34 was updated to handle the new codes.
Support for upgrading the RS232-8 card firmware was removed from Map34. Attempting to read the RS232-8 card's firmware version or attempting to initiate a firmware upgrade results in an SNMP error from the AM3440.
----------
Map34 V1.20 Release Notes 4/29/2016
1.0 INTRODUCTION
This release is for all versions of Map34.
This release corrects a problem reading the cross-connect map when the AM3440 is configured for SNMPv3 access. This problem was related to the SNMP change introduced in Loop firmware v8.41.01 and subsequent support in Map34 v1.18.
----------
Map34 V1.19 Release Notes 2/8/2016
1.0 INTRODUCTION
This release is for all versions of Map34.
This release adds mapping support for the Transfer Trip Card (TTA).
----------
Map34 V1.18 Release Notes 2/3/2015
1.0 INTRODUCTION
Version 1.17 was not released publically.
This release is for all versions of Map34.
This release adds the following:
Map34 is now compatible with an SNMP change introduced in AM3440 v8.41.01 firmware NFS 15000249. Support these cards has been removed from Map34.
card model (4), V.35
card model (5), X.50
card model (6), DTU-10
card model (7), MDSL
card model (9), DTU-6
card model (23), V.35-B
card model (33), RS422-A
Reading the cross-connect table is slower, due to the SNMP change. A status box is displayed showing the progress of reading the table.
----------
Map34 V1.16 Release Notes 2/3/2015
1.0 INTRODUCTION
This release is for all versions of Map34.
This release adds the following security feature:
When a configuration file is protected, Map34 will enforce that the password is a minimum of 8 characters and contain at least 3 of the 4 character types; upper-case, lower-case, numeral, and special-character.
----------
Map34 V1.15 Release Notes 12/29/2014
1.0 INTRODUCTION
This release is for all versions of Map34.
This release adds the following security features:
An option to AES encrypt the .lcf configuration file from a user supplied password. This option can be forced "on" during install.
An option to hide SNMP community and SNMPv3 encryption keys when editing the .lcf configuration file. This option is enabled during install.
A new enterprise licensing feature was added. Dee internal documentation for details.
----------
Map34 V1.14 Release Notes 6/12/2014
1.0 INTRODUCTION
This release is for all versions of Map34.
This release adds the following feature:
Support for the ECA, V110, and ABRA cards.
Support for mapping E1/T1 ports in unframed mode.
License verification was changed. In two controller setups, Map34 will now run if either the primary controller or the redundant controller is licensed. Previously, Map34 required the primary controller to be licensed.
A new private branded version is released. See internal documentation for details.
----------
Map34 V1.12 Release Notes 3/26/2014
1.0 INTRODUCTION
This release is for both the standard version of Map34 and the corporate versions of Map34.
This release adds the following feature:
PuTTYtel was removed from the install package and replaced with puTTY. PuTTY includes SSH support.
----------
Map34 V1.11 Release Notes 1/15/2014
1.0 INTRODUCTION
This release is for both the standard version of Map34 and the corporate version of Map34.
This release adds the following feature:
A copy of PuTTYtel is included in the install package and will co-install with Map34. PuTTYtel is both a terminal emulator and a telnet client. Map34 has been modified to launch PuTTYtel directly from the tools menu, giving the user a quick and easy way to open a console session with the AM3440.
----------
Map34 V1.10 Release Notes 12/31/2013
1.0 INTRODUCTION
This release is for both the standard version of Map34 and the corporate version of Map34.
This release corrects the following:
There is a bug in the AM3440 firmware when reading the LS-Optical Card's Information Table. This is a reoccurring issue with Loop where an SNMP object can't be read with an SNMP GET operation but can be read with an SNMP GETNEXT operation. This version reads the necessary information using GETNEXT instead of GET.
Corrected a message box displayed during TFTP File Transfer with a typo.
Corrected a problem displaying the TFTP File Transfer status during a firmware upgrade.
----------
Map34 V1.09 Release Notes 9/5/2013
/1.0 INTRODUCTION
Version 1.08 was a test version that wasn't released.
This release is for both the standard version of Map32 and the newly generated corporate licensed version of Map32.
The corporate licensed version is identical to Map32 other than the way it handles license keys. See internal documentation for that version. The corporate licensed version maintains configuration file compatibility with the standard version of Map34.
An integrated TFTP server was added to Map34 that allows the user to easily send and receive configuration files and to send firmware images to the AM3440. Access to this feature can be found under the "File - Transfer" menu.
----------
Map34 V1.07 Release Notes 9/6/2012
1.0 INTRODUCTION
This release allows E&M cards to be mapped either as voice or data without regard to the "transmit only" setting.
----------
Map34 V1.06 Release Notes 3/1/2012
1.0 INTRODUCTION
This release adds the following features:
Added the option of selection either Voice or Data when mapping an E&M card configured for Tx Only signaling. Previously Map34 would force the mapping to voice. The mapping will still be forced to voice if the card is not configured for Tx Only.
This release corrects the following:
There was a memory leak whenever the user selected a different AM3440 or did a refresh operation.
----------
Map34 V1.05 Release Notes 9/6/2012
1.0 INTRODUCTION
This release adds support for the 8UDTE card.
----------
Map34 V1.04 Release Notes 4/11/2012
1.0 INTRODUCTION
This release adds the following features:
A print screen feature was added. It can be found under the "File" menu.
If the user enters more than 6 digits for a controller serial number, only the last 6 digits are accepted.
----------
Map34 V1.03 Release Notes 1/23/2012 1.0 INTRODUCTION This release adds support for mapping ULSR.----------
Map34 v1.02 Release Notes 1/10/2012
1.0 INTRODUCTION
This is the initial release of the Map34 Software.
----------
 |
|||
| Data Comm for
Business Inc. 2949 County Road 1000 E Dewey, Il 61840 |
Voice:
217-897-6600 Toll Free: 800-4-DCB-NET Toll Free: 800-432-2638 |
Email: Contact Page Web: www.dcbnet.com Fax: 217-897-8023 |
|
| All DCB web pages copyright ©1995- Data Comm for
Business, All rights reserved. EtherPath®, EtherSeries®, EtherPoll®, EtherBridge® and EtherModem® are Registered Trademarks of Data Comm for Business, Inc. |
|||