OEM 56K DSU

56 Kbps DSU/CSU with TTL Interface for OEM Applications

FEATURES
DESCRIPTION
SPECIFICATIONS

General
Indicators (front panel)
Controls
Telco
Data Port
Physical/Electrical

APPLICATION

FEATURES

56 Kbps
TTL interface
DCB will customize
Synchronous
Point-to-point or multipoint
DDS service or line driver mode
Responds to Bell defined current reversal loopback and non-latching loopback
Exceeds Telco RX attenuation specifications by more than 10 dB

The DCB 56 Kbps OEM DSU/CSU is a 56 Kbps synchronous DSU/CSU for use with DDS or equivalent digital services. The DL-56 complies with Bell system encoding, decoding, timing, interface and diagnostic standards. It will operate point- to-point or multipoint. The DL-56 has a master clock mode that allows it to be used in line driver mode over customer owned cable.

The DL-56 OEM DSU is easy to implement. It requires a simple 5 volt DC power supply. The OEM board has TTL logic output for the data and control leads. It also includes complete indicators and the controls necessary to control clocking, loopbacks, and point-to-point or multipoint operation. For a moderate fee, typically ranging from $5,000 to $10,000, the OEM DSU board can be provided in custom form factors. The board can be as small as 25 square inches. DCB will manufacture the unit or will license manufacturing.

The DL-56 uses the latest line interface technology, which exceeds digital services attenuation specifications by more than 10 dB. This translates into longer cable distances from the phone company central office to the customer premise, or longer customer owned cable runs for line driver applications.

The DL-56 is easy to install and operate. The few controls on the unit include the loopback selection of line driver or phone company clock, and Request to Send control for multipoint operation. The minimum number of controls and comprehensive indicators make installation and troubleshooting easy. Diagnostic aids built into the DL-56 include LED indicators and loopback capabilities.

The DL-56 is an ideal choice for any application requiring 56 Kbps digital service, including bridging, multiplexing and multidrop lines.

SPECIFICATIONS

General

Rates: 56 Kbps synchronous
Application: Point-to-point or multipoint
Facility: Dataphone Digitial Service (DDS) or equivalent, Line driver mode for customer owned 4-wire circuit

Indicators (front panel)

Transmit Data, Receive Data, Request to Send, Clear to Send, Data Carrier Detect, Test

Controls

DIP switches for Bidirectional Loopback, master or slave clock, RTS controlled by terminal or forced on.
Responds to telco current reversal loopback and non-latching pattern loopback.

Telco

Interface: DDS bipolar return to zero
Connector: 8-wire RJ-48S

Data Port

Connector - 14-Pin, 2 rows by 7pins on 1/10" centers
Interface: TTL
Timing: Synchronous

Physical/Electrical

Power requirements: 5 volts DC
9" x 5" printed circuit board
The DSU compononents can fit in as few as 25 square inches
Custom board sizes and layout are available. Call DCB for more information.

Data Comm for Business Inc.
2949 County Road 1000 E
Dewey, Il 61840 Voice: 217-897-6600
Toll Free: 800-4-DCB-NET
Toll Free: 800-432-2638 Email: Contact Page
Web: www.dcbnet.com
Fax: 217-897-8023

All DCB web pages copyright ©1995- Data Comm for Business, All rights reserved.
EtherPath®, EtherSeries®, EtherPoll®, EtherBridge® and EtherModem® are Registered Trademarks of Data Comm for Business, Inc.



Data Comm for Business Inc. 2949 County Road 1000 E Dewey, Il 61840	Voice: 217-897-6600 Toll Free: 800-4-DCB-NET Toll Free: 800-432-2638	Email: Contact Page Web: www.dcbnet.com Fax: 217-897-8023
All DCB web pages copyright ©1995- Data Comm for Business, All rights reserved. EtherPath®, EtherSeries®, EtherPoll®, EtherBridge® and EtherModem® are Registered Trademarks of Data Comm for Business, Inc.