SR Multiplexer Internal Dial-Up Modem
Configuration Instructions

March 4, 1999

SR multiplexes are now available with an optional internal modem.

To configure the SR multiplexers to work with the optional internal dial-up modems, attach a terminal or PC to the SR Network Management Port using the green cable and the appropriate adapter (supplied). When you see "At your command >>", follow the instructions below. User responses are shown in BOLD.

HOST MULTIPLEXER

AT YOUR COMMAND >> CN(enter)

CONFIGURE NETWORK
-------------------------------
 SYNC MODEM
 LEASED LINE
 ERROR CORRECTION ON  

SYNC or ASYNC modem? [S/A] >> A(enter)
ASYNC rate? [9600 / 19200 / 38400 / 57600 / 115200] >> 57(enter)
Leased or Dialup Line? [L/D] >> D(enter)
Enable Error Correction? [Y/N] >> Y(enter)
Disconnect timeout? [1 to 99 min; 0=Disable] >> 0(enter)
One-Touch Dialing? [ATDS0 / DTR Dial / OFF] >> OFF(enter)
Send SR call progress messages? [Y/N] >> N(enter)

 ASYNC MODEM: 57600  
 DIALUP LINE
 ERROR CORRECTION ON  

Configure Modem? [Y/N] >> Y(enter)
*** CONFIGURE MODEM - Type ESC ESC to stop
at(enter)
OK
at&f &q6 s0=1 &w(enter)
OK

Type (ESC)(ESC) to return to AT YOUR COMMAND.

*** End CA/CC Capture

AT YOUR COMMAND >> 

REMOTE MULTIPLEXER

AT YOUR COMMAND >> CN(enter)

CONFIGURE NETWORK
-------------------------------
 SYNC MODEM
 LEASED LINE
 ERROR CORRECTION ON  

SYNC or ASYNC modem? [S/A] >> A(enter)
ASYNC rate? [9600 / 19200 / 38400 / 57600 / 115200] >> 57(enter)
Leased or Dialup Line? [L/D] >> D(enter)
Enable Error Correction? [Y/N] >> Y(enter)
Disconnect timeout? [1 to 99 min; 0=Disable] >> 0(enter)
One-Touch Dialing? [ATDS0 / DTR Dial / OFF] >> AT(enter)
Send SR call progress messages? [Y/N] >> Y(enter)

ASYNC MODEM: 57600
DIALUP LINE
ERROR CORRECTION ON

Configure Modem? [Y/N] >> Y(enter)
*** CONFIGURE MODEM - Type (ESC)(ESC) to stop
at(enter)
OK
at&f &q6(enter)
OK
at&z0=nnn-nnnn(enter)    Note: Replace nnn-nnnn with the phone number of the HOST Multiplexer.
OK
at&w(enter)
OK
(ESC) (ESC)
*** End CA/CC Capture

AT YOUR COMMAND >> 

ONE-TOUCH DIALING

To make a connection to the host pressthe space bar or (enter) from any terminal connected to the remote multiplexer. When you see "SR: Connected" you should be able to log in from all remote terminals. If you set the remote multiplexer Disconnect timeout to a number between 1 and 99 (minutes), the connection will hang up if there is no activity from any terminal for that period of time. To re-establish the connection, press the space bar or (enter) from any terminal.

img
Data Comm for Business Inc.
2949 County Road 1000 E
Dewey, Il 61840
Voice: 217-897-6600
Toll Free: 800-4-DCB-NET
Toll Free: 800-432-2638
Email: Contact Page
Web: www.dcbnet.com
Fax: 217-897-1331
Shopping cart is
HACKER SAFE certified sites prevent over 99.9 of hacker crime.
All DCB web pages copyright ©1995--2016 Data Comm for Business, All rights reserved.
EtherPath®, EtherSeries®, EtherPoll®, EtherBridge® and EtherModem® are Registered Trademarks of Data Comm for Business, Inc.